Snow bros 2 jamma12/28/2022 ![]() However to be sure it definitely wouldn't hurt if you tried 320x240 optim also. Since this was not the case for your Knuckle Bash, I think this is already a big sign that it is incompatible. However, with the OSSC-compatible Toaplan V2 games, you typically already get a nice (at least stable and otherwise free of major errors) picture on all-defaults/Generic 4:3. Using that, you may be able to get something, like an intermittent image, provided your TV is not too picky and cooperates. timing - 320x240" and set an H.samplerate of or around 1250 for example. Successfully managed to mask that.Īll the results I posted here have this as as baseline, everything else default, then changes from that as I posted them. Thanks for your tests, and - mea culpa! My OSSC was in Line 3x/320x240 optim mode the whole time, because like you I was not able to get any image at all using Generic 4:3. My Snow Brothers 2 won't arrive for about 60 days however. ***Since this isn't the hardware everyone in this thread is taking about though, I guess I need to find my Fixeight and Truxton 2 now to test, but I'm sure I'll have same results as the experts here. Had to set it to 3x mode with v.backporch to 29 to get both sides (top and bottom of TV left and right game screen) to fit. Only issue is screen is cut off a bit on the bottom of my TV (right of the game, as in player 2's side). Works fine on start up, 2x, 3x, and 5x generic modes. Did the settings reset on the OSSC, then tried OZ. timing" setting should I be under when I move the H.samplerate to 1k, 1.1k, 1.2k, etc? I'm using Line 3x mode, set in Generic 4:3?ĮDIT 3: By the way, I'm not crazy, my Outzone works great. I also popped in a Strikers 1945 PCB which works fine on the same settings.ĮDIT 2: Hmm, since I'm not an expert in the OSSC, what "Adv. Sorry, I do not have a scope, but am happy to try any settings you like with what I have.ĮDIT 1: I should add that I forgot the FW update wipes my old settings, so when I put it on 3x mode generic, the OSSC green light stays on and the red light does go off, but still nothing on my TV (to include not seeing the OSSC OSD or sound). 85a FW I get this on the screen:Īnd I tried raising the H.samplerate to 1000, 1100, and 1200 with no affect (although please explain which H.samperate I should be adjusting). To the OSSC via the same SCART cable however, on a fresh. I'm using a HAS supergun which works fine via SCART to RetroTINK RGB2COMP box to component into a NTSC TV. When plugged in I get the red and green LEDs on the OSSC with nothing displayed on the TV. OK, so I found the Japanese Knuckle Bash PCB (still looking for Korean one). These games all work with the OSSC as far as I have seen! No need for examining Out Zone as that's Toaplan V1 hardware. 2 would be interesting, I don't think the difference between the Japanese and Korean version of Knuckle Bash should matter, but you can of course try both if you wish. Look for the Vblank area and measure the period p1-5 as shown in this image: click If you have an oscilloscope, you can ensure that it's indeed the problem discussed here by measuring the Csync signal. In addition, it would confirm the aforementioned thesis. The latter would mean that the game has the Sync glitch responsible for the OSSC incompatibility. If not, try increasing H.samplerate very liberally (1000+) and see if you can get an (intermittent) picture this way. Simply check if you can get a stable picture with the OSSC on default settings. As I posted before, I think my Outzone works with my HAS to an OSSC. I'd be happy to test, but I'd need some info on what you're looking for exactly. I have two Knuckle Bash PCBs (Japanes and Korean) and a Snow Bros.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |